KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

17th January 2019

Positioning itself as a midrange product, Paul Rigby exhaustively reviews the Kirmuss KA-RC-1 ultrasonic vinyl record cleaner. This is Part Two of a two part review. 

To repeat, this is the second of a two part review on the Kirmuss KA-RC-1 ultrasonic vinyl record cleaner. If you have yet to read the first part then I would strongly advise you to do that now by clicking HERE. Otherwise, you may be a tad confused by the following.

One of the issues with the KA-RC-1 cleaning cycle as a whole is the length of time that’s required to attend to each and every record. Kirmuss might add, “Well, if a job’s worth doing, it’s worth doing well.” And that the time taken is worth the final result.

I wondered about this.

A major slice of time is taken up with Kirmuss’ After Care system. When you finally take the record out of the record cleaning machine and that record has completed its ultrasonic cleaning cycle, you would think that the cleaning process would be over at that point. Not so. In fact, Kirmuss has plans for you and your record. There’s further cleaning steps to be completed before Kirmuss will let you go. 

Before I begin, allow me to describe the After Care toolkit. You are suppled with a small mat, upon which you’re supposed to place the record while performing the After Care. There’s a couple of small microfibre cloths, the type you might receive free with a new pair of glasses. There’s a Kabuki brush (a stubby, dense bristled brush commonly used by ladies for make-up purposes) that is used to both apply surfactant and, later, a ‘rinse’ of distilled water. You’re also given a combo carbon fibre brush/felt sponge on a flip-over swivel axle. To use the desired brush or sponge, you rotate the brush. A thick cloth bedecked with pictures of bunny rabbits <sigh> is also supplied which can be used to help in drying your hands and cleaning the Kabuki brush from time to time. A bottle of blue stylus cleaning liquid is also supplied (I would recommend ignoring it and using a sticky pad system, such as the DS Audio ST-50 or one of several other specialist items currently on sale).

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Kabuki brush

For the After Care section, you are asked to place the record on the miniature mat (felt side uppermost). You spray your record with distilled water (which you must buy – I bought a small empty hand spray bottle from the local chemist to do this bit). The distilled water is then worked into the grooves to, as Kirmuss says, “rinse” them by the Kabuki brush. That water is then dried and mopped up with the microfibre cloth. Then the sponge side of your combo brush is run around the record’s surface to lift excess water. After that, you add a touch of surfactant to the brush. Only a tiny amount is added. You do this by spraying into the air and then pushing the brush into the cloud which coats the tips with a small amount of the liquid. The brush is then run around the record. The reason for this, says Kirmuss, is to prevent static electricity build up. After that, you then run the carbon brush side of your combo brush around the record.

Of course, that’s a single side of vinyl record application. You’ll then need to flip the record over and repeat the entire process again on Side B. Even typing this process is exhausting. Never mind doing it.

Nevertheless, I had issues with most of this, I’m afraid 

Firstly? Your work mat, the little felt mat that you’re supposed to place your vinyl disc upon to do all of this After Care work? It’s too large. There’s a risk too of re-contamination of the vinyl grooves from the felt mat. The solution? Either measure a circle diameter with a compass and trim or find an alternative. I’m still looking. Does anyone out there with Kirmuss experience have any ideas?

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Felt mat (rear)

Next? The use of the microfibre cloths and the sponge side of the 2-in-1 brush may soak up excess water but you do find that you physically press on the grooves to do this. Isn’t there a threat, therefore, that any fragments of dirt hanging onto the grooves for grim death may then be pushed back into grooves, recontaminating them? Aren’t all of these actions counter-productive, to the cleaning process, therefore?

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Felt mat (front)

Then there is the recommended “rinse”. Initially, I wondered why you needed to rinse the record in more distilled water. Haven’t we just cleaned the disc? Hasn’t the surfactant supposedly melted away and fallen into the water? Hasn’t the alcohol now evaporated from the disc upon emerging from the KA-RC-1? What exactly are we trying to rinse here? I have to also ask, how does dousing the record in water and then mopping it up with a lint-free cloth constitute a rinse?

I’ll talk more of this later.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Multi-purpose Kirmuss cloth or, alternatively, audiophile snuggle blanket for when vinyl fans want to go bye-byes

As for the application of small levels of surfactant to the vinyl surface once more for anti-static purposes, haven’t we just been using the KA-RC-1 to try to remove as much gunge, muck, dirty and dried crud? Why then are we once more adding surfactant to the grooves? The same stuff that apparently can only be removed from the grooves if dissolved fully in water and ultrasonic bubbles? Even if the general idea is to prevent static, aren’t you also adding a new substance to the grooves? Doesn’t that partly defeat the entire reason for using the KA-RC-1 in the first place?

If static prevention is the aim, why not promote the use of a Zerostat or the anti-static Furutech brush or Furutech DeStat? After use, none of these devices leave a residue on the groove surface.

SOUND TESTS 2

To see if the After Care process affected sound in any way, I cleaned my old Ritchie Havens record in the KA-RC-1. I had already cleaned this LP via the Kirmuss 10+ times so that the record was a clean as it was ever going to get.

I then did two things. I cleaned the record again, applied the full After Care treatment and listened via my reference hi-fi. I then cleaned the record once more, ignored the After Care and then did nothing more than air dry the record in a rack, used the carbon fibre brush to dislodge and final bits of rubbish and then played the record again.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Carbon Fibre brush

The result? As I feared, the After Care-affected record added a veiling layer to the record surface. The midrange, especially the upper mids, was slightly blunted and a little rolled off at the extremities. Dynamic range was snipped at the far end while treble was a little dull.

I put the blame for the veiling directly at the final application of the ‘anti-static’ surfactant. Once the veiled record surface was cleaned again by the KA-RC-1, the surfactant was dissolved and washed away and the dynamics were restored again.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

The brush can be swivelled to reveal the felt pad side

If the surfactant is added during this time to act as an anti-static application, not only do you add a sonic veil but your stylus then scoops the stuff up and collects it onto the tip. You then spend more time cleaning your stylus tip.

HIGH DOSAGE

More than that, if you add surfactant earlier, during the basic cleaning cycles using the above-mentioned spray applicator then way too much is added to the grooves. The dose is too high. It takes a long time to get rid of this stuff. You’ll find that it will collect on your stylus for some time to come. Because of the spray action, I had to introduce a separate active rinse cycle, spraying the surface of my record with distilled water, brushing it in and rinsing the record again in the KA-RC-1 for up to 10 minutes. Not practical.

Because of my earlier health concerns (see Part One for the full story) and because I binned the spray, replacing it with an eye dropper pipette, I was able to reduce the surfactant dose. Instead of three large sprays in the 12, 4 and 8 o’clock positions, I recommend almost painting a thin line of surfactant with the tip of the eye dropper at the 12, 3, 6 and 9 o’clock positions. The amount of surfactant is vastly reduced and much less is dumped in the grooves. I found next to no surfactant collected on my stylus after this treatment.

AIR DRY OR NOT?

Once you remove the wet record, instead of pushing the muck back into the grooves with the Kirmuss-recommended cloths and sponges, you can air dry in a rack. You can use a rack that you may have fashioned yourself or, if you happen to have a Disco Antistat, that manual washer has an excellent drying rack. The rack prongs that are not too high, keep the records vertical but, at least for 12” records, only touch the run out grooves with plastic tips on the end of the racking prongs.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

The rack component from the Disko Antistat manual cleaner. A useful air dry accessory for the Kirmuss RCM

There is a better and higher-end option here: use the vacuum pump from a ‘spare’ RCM or, indeed, buy one in especially for the purpose. This vacuum RCM will cut drying/waiting times to a fraction, will remove the liquid plus any loose material hanging around the grooves and further reduce latent gunge collecting on the stylus. Something like a Moth, VPI or similar. If you do use a machine like this, take extra care not to reinfect the grooves with the vacuum arm’s felt layer. The bit that comes into contact with the record. I would recommend cleaning this felt after each and every record side. Also, as the Kirmuss rinse cycle cleans and wets both sides, be sure to dry the vacuum RCM turntable with a dry cloth before you flip the record over.

My luxury choice, though, was a Loricraft RCM which has the best vacuum system currently on the market. The vacuum pump never actually touches the record surface and addresses each part of the record slowly and carefully. You’re talking a hefty piece of spare cash for a Loricraft but, if the option is there, then I’d go for the Loricraft just for its vacuum option. Thinking about it, a combo KA-RC-1/Loricraft or KA-RC-1/VPI or KA-RC-1/Moth or whatever combo you choose compares favourably in cash terms with an Audio Desk ultrasonic cleaner. So maybe the idea is not so silly, after all.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

A Loricraft RCM can be used as a drying tool for the Kirmuss – although any vacuum-based RCM could do the job

So what’s the recommendation for the Kirmuss After Care session? By all means use the carbon fibre brush for a final physical clean of extraneous dust or lint before play but, apart from that, bin the rest of the stages. They’re a waste of time and they cause issues. Then think carefully about the drying action in terms of air drying or bring in a vacuum RCM.

AN ALTERNATIVE SURFACTANT

If you buy a KA-RC-1, what happens when you run out of surfactant? You will need to buy another bottle. According to my research, each new bottle of Kirmuss surfactant costs £20 for just 60ml, which is extortionate! Kirmuss needs to look at this. 

If you want to consider another option then I have an alternative that I thought was as good as the Kirmuss system, during my own sound tests.

Oddly enough, it includes the liquid supplied by competitor, Audio Desk for its own RCM. This liquid includes a surfactant. Audio Desk asks you to buy a little bottle of concentrate for £14. You then dilute this concentrate in five litres of distilled water. Instead of using that to fill an Audio Desk RCM, I would advise applying small amounts to the face of a vinyl record as an external surfactant. I would fill one of my favourite pipette bottles with just a small amount from that five litre source (which will last for ages).

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Once done, I would then add half a pipette of Propylene Glycol (as discussed in Part One of this review) which can be bought HERE. This bottle will also last for ages. The Propylene Glycol will give the Audio Desk liquid a bit of bulk. When added, you shake the bottle to mix the two liquid.

When mixed, apply a full pipette around the record surface in a circle. Keep the record surface level for now and using the Kabuki brush work it into the grooves, follow a circular motion, covering the entire surface. Do that three times. Then grasp the near end of the brush to form a stiff bristle and work the surfactant into and along the grain of the grooves. Work in a spiral manner along the groove direction. Then repeat on the flip side and the record is ready for cavitation.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Plenty of suppliers offer Propylene Glycol – I offer a link to one of those, above

If you find that, during play, the stylus is accumulating gunk, you’ve probably added too much Glycol. Just back off on the quantity a bit and make up a new bottle. You’ll have plenty to use for experimentation.

The Propylene Glycol will keep the surfactant in place in the grooves until cleaned by the cavitation and alcohol. Using a minimal amount of Propylene Glycol will mean less will collect on the stylus tip.

Doing it this way, each 60ml bottle should cost you around 25p instead of £20 as Kirmuss demands.

Before I move on, if you decide to buy larger value packs of Propylene Glycol  to make your own surfactant be careful that you purchase the correct liquid. Make sure that you buy Propylene glycol. Do NOT – I repeat, do NOT buy Ethylene glycol. The latter is nasty, can cause major problems if ingested, breathed in and the like. I’m talking central nervous system issues…brain problems…how about coma? You catch my drift on this one? Oh, and if your pets drink it accidentally, it will kill them. So then, double check that you’re buying the correct formula, eh? Propylene glycol is fine. Ethylene glycol is not.

SOUND TESTS 3

How effective can the KA-RC-1 be? How efficient is it? What are its potential cleaning possibilities? How far can it go? I wanted to test this area using, not just a dirty record but one that is full of hard, encrusted gunk. 

I came across one such LP in my own collection. It was a Sarah Vaughan album on the Mainstream label, a live show in Japan. I cleaned it twice on the Kirmuss, on both occasiobs, I used surfactant scrubbed into the grooves and a total of two cycles of five minute ultrasonic cavitation.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

The motor housing that rotates the built-in gearing and your records during the cavitation process

Kirmuss says that such bunged up records can be spotted by the grease-like substance that emerges on the grooves surface when the surfactant is worked in by the brush. I must admit that I didn’t see that at all. Nevertheless, if my eyes missed this so-called Kirmuss effect, my ears spotted it immediately. Playing the record immediately afterward two separate cleaning cycles was a horrendous experience! Truly poor. It sounded like the stylus was caked with muck. Yet, upon inspection, the stylus was clear. What was it? It was muck and grime that was slowly lifting off the groove floor and sides because of the early cleaning cycles and rising inexorably to the surface. It just hadn’t got there yet. So, in effect, the sound quality was worse than when I began. If this happens to you, don’t panic. In fact, see it as a good thing. A work in progress, you might say.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Sarah Vaughan – drowned in gunk

So I gave the record two more cleaning cycles. The results were better but not perfect. Another two cleaning cycles were employed (now, six in all). And that did it. The record sounded a little damaged around the edges but startlingly brilliant in broad terms. A RCM cannot repair a damaged record but the final sound was superior than the sonic experience I had previous to the clean. There were some beautiful upper midrange highlights here with a bass that could be actually heard for once. Instrumental separation now existed for the first time and the soundstage offered a genuine 3D depth. Hurrah!

The moral of this tale? Be prepared to experiment, tweak and thoroughly mess around with your records and this RCM to get the vinyl performance you want. You may have to keep at it, though. I had to clean this record six times but be prepared for more.

DISCLAIMER

I finally felt that I was getting somewhere with the KA-RC-1 but one thing bothered me. The KA-RC-1 did as well as the Audio Desk RCM in terms of removing gunk and muck but the Kirmuss sounded better in sonic terms. As I said in Part One, I felt the reason for that was the use of a tiny amount of alcohol in the bath in the Kirmuss RCM. The Audio Desk didn’t feature any alcohol in its bath when I compared it earlier. 

What if I added alcohol to the Audiodesk then? Would that enhance the Audio Desk’s sonic performance? How would an alcohol-fed Audio Desk perform against the KA-RC-1? Wouldn’t that be a fairer comparison between the two? The ultimate shoot out?

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

That’s what I did but I don’t recommend that you do it. Why? Because, apparently, adding the tiniest drop of alcohol into an Audio Desk RCM will remove the warranty on the affected machine. So, officially, I would encourage you NOT to add any alcohol to the machine at all. DON’T DO IT! If you use alcohol in the Audio Desk vinyl cleaning machine and you later suffer a technical hitch to your Audio Desk RCM but the machine is rejected by the host company because of your prior alcohol use in the RCM then BE IT ON YOUR OWN HEAD. Don’t say that I didn’t warn you.

Going against the grain and breaking rules is part of my job, though. So in went the alcohol in my machine. The same amount: 0.43% of the total water volume.

SOUND TESTS 4

My first test will probably enrage Audio Desk but it was an option I had to try to cover all of the options fully. The Kirmuss uses 0.43% of alcohol in its bath. So I did the same to the Audio Desk. That is, I added 0.43% of alcohol to the Audio Desk bespoke cleaning liquid/distilled water combo and listened to that.

I played my Ritchie Havens track again and the result was pretty good. The sound opened up from its previously rather dull offering to one where the vocal was more expressive and emotive. Previously, the guitar strums dragged a bit, slowing the track. Now, the attack was more immediate and the transients were faster. I gave the LP a second cleaning cycle in the Audio Desk but found no obviously beneficial extra sound quality from this second cycle.

Then I moved on to the next level. I totally drained the Audio Desk-based liquid, cleaned the internals of the RCM and refilled it with nothing but distilled water and 0.43% alcohol. The Audio Desk bespoke liquid was not added this time. That is, Audio Desk’s own cleaning liquid was not part of the bath’s contents.

I played Emmylou Harris and You’re Free to Go from the album, Thirteen. The sonics improved still further. The upper mids where now extended as was the dynamic range. The resultant sound was never harsh nor bright but was just a tad edgy. There was a beautifully transparent quality to the sound but there was a slight, just a slight sharpness to the sound.

Next, I added Kirmuss surfactant to the surface of the Emmylou Harris LP to see if this step added something to the sound. It certainly did. All of the above sonic qualities remained but the soundstage appeared to extend left and right while the sound now had a richer, more mature aspect. It was balanced with, critically, no edge or sharpness.

Repeating this cycle a second time, including a second application of the surfactant improved matters still further. Mids were smooth, treble was extended and more information was available.

OK then, so here’s the crunch. Using the two-cycle process of surfactant application to the vinyl surface followed by an ultrasonic clean, which RCM was the best in sonic terms? The Kirmuss or the Audio Desk?

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Emmylou considering her ultrasonic options

The results were interesting. The Audio Desk was the best in terms of control and maturity within the midrange, treble offered better structure and bass was tonally more interesting. The Kirmuss could be a little wayward in how it handled the overall frequency range. The Audio Desk was rather more coherent in this respect.

That said, the KA-RC-1 remained excellent in terms of its sonic performance. In purely sonic terms, there was plenty of detail on offer, clarity and transparency were both excellent the dynamic reach was impressive.

What the Audio Desk had up its sleeve was a chassis and mechanism that was wholly bespoke to the task of cleaning vinyl. This test proved that the chassis and all that mechanical gubbins inside really does matter. That’s what the Audio Desk is made to do – that’s why you pay so much cash for it. The Kirmuss, may I remind you, uses an off-the-shelf model that was tweaked for vinyl use. I feel that the tailored design of the Audio Desk told in the end. So, to repeat, given a level, alcohol-soaked, surfactant-strewn, playing field, the Audio Desk is the obvious and clear winner. Records sound better from the Audio Desk under these conditions.

That said, I’ve been using a ‘naughty’ version of the Audio Desk for these tests, complete with alcohol and surfactant. An Audio Desk from the wrong side of the tracks, you might say. An Audio Desk from the Dark Side.

Hence, officially, this test doesn’t exist because Audio Desk rejects the use of alcohol and doesn’t sanction the use of an external surfactant. Audio Desk wants you to use its own cleaning liquid. So, in official terms, at this stage of the game, the Kirmuss is the clear winner. And that’s how it’ll be (officially) until Audio Desk changes its mind and its focus. If and when it does, though…

CONCLUSION

There is just a touch of the P.T. Barnum about Kirmuss. I say that with a smile on my face because I have no wish to insult or denigrate the company. They mean well but the outfit brings this feeling upon itself.

If you attend one of its demos, you’ll see the man in the white coat, the Ringmaster’s badge of supremacy, acting like the barker Billy Bigelow in the Hollywood musical, Carousel. He’s designed to impress.

The company offers thrills and spills. It scares you with its warnings about encroaching fungus, tales that will keep any vinyl fan up at nights, a substance that threatens to cover your vinyl as Jeff Wayne might describe the Red Weed in his version of H.G. Well’s The War of the Worlds.

There are magical illusions such as the never-ending emergence of magical grease from the vinyl groove that forever spews forth like multi-coloured handkerchiefs from the mouth or some sort of analogue ectoplasm that requires the immediate assistance of the Kirmuss Ghost Busters.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

There’s even the mysterious Charles Kirmuss, the man of a thousand talents, his wonders to perform (according to his adoring staff).

And it doesn’t help. None of it. Despite what Kirmuss might think. The above adds a sense of the suspicious to the company. A nervous element. You wonder how far you can trust this lot.

Yet, from what I can gather Kirmuss, as a company, has the best of intentions. I’ve talked to them a lot and that’s my feeling. It just tries too hard and it comes out wrong. It doesn’t really need to. Kirmuss has a good product here. They could turn it into a great product. They could even turn this product into a minor industry all of its own. If Kirmuss would just step off its marketing pedal with it’s eccentric manual and its slightly bizarre website and its overly quirky persona then the green gas would clear and we would all see that.

My tests prove it to me, at any rate. The core KA-RC-1 is a good product. It does the job and it does the job well. Yes, the footprint of the KA-RC-1 is very large, yes you really don’t need the After Care gear, yes you need to tweak the cleaning system to fit your circumstances and yes the basic design of the machine looks like a 12 year old’s toy but the price is about right, the performance is bang on and the core research from the design team is thoughtful and even innovative.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

Turn to the Open position to release the bath of distilled water/alcohol through the nozzle (right)

This new machine will – or should – inject the flowering ultrasonic market with a few shivers. The competitors need to look closely at what Kirmuss is doing right. They need to consider the flexibility of the Kirmuss technology. They need to re-look at the use of alcohol as part of the cleaning process.

The KA-RC-1 isn’t perfect, though. The more expensive machines out there do some things better: they offer a smaller footprint, an automatic cleaning system that people actually like with an assured feeling that the machine has everything in hand. This approach can be comforting to many. This is an important factor for many buyers. If you look at the Kirmuss tests above and wonder if it’s all too much effort and trouble, then avoid the KA-RC-1 and stick with a product like the Audio Desk.

Your buying decision should be based on your priorities in terms of vinyl cleaning, as well as your budget.

KA-RC-1 ULTRASONIC FROM KIRMUSS PT.2

The internal bath area showing ultrasonic transducers. You may be able to see the grime bits that have been cleaned from the test records.

Think of it like this, the automatic RCM types like the Audiodesk are the Apple Macs or the iOS devices of the ultrasonic world. They are beautifully designed, offer a tailored and bespoke chassis and wall you off from the real world. They offer security but little freedom. 

The open and flexible nature of the Kirmuss means that it represents a PC-like or Android-type of device. Imminently flexible and tweakable. With enough features and options to fit the needs of any audiophile who likes to dabble, experiment and doesn’t mind spending time on the machine to get it right while getting his hands dirty (or clean…this is a RCM, after all).

But there is that bottom line, isn’t there? One that needs addressing. And so I ask, is the Kirmuss a recommended cleaning machine? And the answer? Well, if you’ve read this feature all of the way through then you’ll know that the answer is a little complex. Firstly, because you’ve got to factor in Kirmuss the company who just insist on getting in the way and trying its best to undermine and diminish its own machine. A truly bizarre situation, via its eccentric and less than satisfactory cleaning recommendations. If pushed, at this specific moment in time, at this price point (very important), in terms of its flexibility and potential, the default format options available and in terms of its sheer sonic improving performance then the KA-RC-1 is recommended.


KIRMUSS KA-RC-1 ULTRASONIC CLEANER

Price: £1,197.60 (shop around, I have seen it on sale for £995)

Website: www.kirmussaudio.com


GOOD: cleaning performance, sonic qualities, default disc formats, carry handles, tweakability

BAD: manual, after care stage, the company itself

RATING: 8


[Don’t forget to check out my Facebook Group, The Audiophile Man: Hi-Fi & Music here: www.facebook.com/groups/theaudiophileman for exclusive postings, exclusive editorial and more!]

REFERENCE

Origin Live Sovereign turntable

Origin Live Enterprise 12″ arm

Van Den Hul Crimson XGW Stradivarius Cartridge

Soundsmith Paua Mk.II cartridge

Icon PS3 phono amplifier

Aesthetix Calypso pre-amp

Icon Audio MB845 Mk.II monoblock amplifiers

Quad ESL-57 speakers with One Thing upgrade

Tellurium Q Silver Diamond cables

Gekko Purple Haze cables

Blue Horizon Professional Rack System

Harmonic Resolution Systems Noise Reduction Components

CAD GC1 Ground Controls