The Article
UPGRADING YOUR TURNTABLE: Why Not Start With the Cartridge?
1st December 2016
For analogue fans, says Paul Rigby, upgrading your hi-fi doesn’t have to mean replacing your turntable…well, not all of it, at any rate
The opinion might have become stronger since vinyl entered its relatively recent renaissance period but there is a school of thought that, if you want to improve the sound quality of your analogue chain, you upgrade your turntable.
This is, of course, a valid option and, for many, a perfectly reasonable plan. Improving the quality of your source will, ultimately, enhance the sound quality of your entire hi-fi. You’re also right to look at the turntable as the first and main target when looking to improve your hifi chain’s sonics. After all, this is where your music begins. Get it wrong here and no amplifier or speakers, no matter how much they cost, will help to improve fatal turntable-derived mistakes. If your turntable is producing sub-standard sound quality then your amp and speakers might change the tone here and there but that quality will not improve. So, yes, the turntable is the first port of call when looking to upgrade.
But do you actually need to change the turntable? Is there a way to enhance the quality of the sound without spending out a lot of money on a new deck? Some of us are lucky enough to do just that. Your £300 turntable not good enough? Upgrade to a £1,000 model…and then a £3,000 model…and then a £10,000 design. Lovely. If you can afford it. Trouble is, most of us have financial commitments that pull our meagre budget in 20 different directions all at once, so such a luxurious upgrade path is but a fantasy.
There are other ways and other means aren’t there? Well, yes, there are. For example, you can improve the quality of the turntable’s arm and change that. A great idea but one that can be a excessively costly and, if you’re not particularly confident in technical terms, might prove a rather daunting prospect.
How about isolation? That is, placing some vibration-absorbing sorbothane feet under the deck? Yep, good idea and one that will help the sonics and can be done very cheaply indeed. The sonic improvements will be good but can you do even better? Sound improvements that offer big bangs for the buck but don’t require a degree in engineering to complete? Hmmm, swivel your eyes over to the cartridge, hanging off the end of your turntable’s arm. It’s a prime place to begin your sonic improvements and to do so at a relatively low cost. And in two ways. Firstly, you can change that cartridge and put a better quality model in that arm. That alone will improve the sound quality all ‘round. There’s another option too, if your cartridge will allow it (and not all will), you could also possibly upgrade the actual stylus to improve the sound quality.
So, let’s give it a go and see what happens. I’m going to take a popular low-cost deck, the Pro-Ject Essentials II turntable, which arrives with a built in Ortofon OM5e cartridge (basic but of good quality) that retails for around £199. I’m then going to upgrade the cartridge and, hence, the overall sound emerging from the turntable, by replacing the cartridge with an Ortofon 2M Red cartridge for £89. Well, I hope that the sound will improve, we’ll have to see, of course. What I will do is to report the differences between the two cartridges and tell you what you get for your money.
After that, I’m going to replace the 2M Red stylus with a 2M Blue stylus (£130). This is a nice little upgrade path offered by Ortofon which means that you don’t have to buy the next cartridge model up the ladder (the 2M Blue) off the shelf for a whopping £175. As both cartridges share the same body, replacing the 2M Red’s stylus with the 2M Blue’s stylus actually transform’s that cartridge into a real, honest to goodness, 2M Blue.
IN USE
When replacing the Ortofon OM5e with the 2M Red, place the stylus guard on the OM5e before you remove the cartridge from the arm to prevent stylus damage. Remove the screws slowly and carefully and remember that, at the opposite end of each screw, is a tiny nut. Remember to catch both. Remove the nuts and the screws and put them in a secure place. Remove the four wires from the rear of the OM5e. The wires are a tight fit so be firm but gentle. Once done, with the stylus guard still attached, store this cartridge in a safe place. Remove the 2M Red from the box and push those colour-co-ordinated wires in the rear of the 2M Red. Notice that the rear of the 2M Red features colour guides to match each wire. Rest the ‘wired’ cartridge on the turnable’s platter.
Then remove the 2M Red’s screws from the box, push those through the finger lift and then into the arm. This keeps the finger lift in place. Position the 2M Red under each screw and use the supplied screwdriver to screw each into place. Note that the chassis of the 2M Red features a screw thread, so you won’t need those tiny nuts here. Tighten the screws firmly but don’t over-tighten. Re-calibrate the down force figure. This is needed because the 2M Red is a heavier cartridge.
Later, when replacing the ‘red’ stylus for the upgraded ‘blue’, make sure that the 2M Red and the replacement 2M Blue stylus both have their stylus guards fixed into position before you attempt the swop. To remove the 2M Red stylus, I placed fingernails either side of the Red stylus, at the join of the stylus and chassis, and eased the stylus off the chassis. The 2M Blue stylus easily slides and is pushed firmly into place.
SOUND QUALITY
Beginning with Ella Fitzgerald’s Sings Broadway LP and playing the track, Hernando’s Hideaway, you can hear that the 2M Red transforms the sound in just about every area. The difference is quite startling and is a revelation in terms of sonic improvements for the cost. Just in general terms, the music sounds richer and more mature. It’s this ‘grown up’ feel that seems to change the very essence of the Essential II from a simple yet efficient budget turntable to a deck with a measure of authority and depth.
Speaking of depth, the bass is now secure and visible. The OM5e found it tough to project almost any bass at all, some upper bass and lower midrange but not a great deal of the deep stuff. The 2M Red fixes the track with a sense of bass security, giving the music a new lower frequency-based rhythm.
There is also a feel that noise has been lowered because Fitzgerald’s voice has a new clarity and transparency. Most revealing is the fact that there is far more reverb around her voice, especially in the early parts of this track. The space and air surrounding her voice adds to the drama and the portentous nature of the music, adding a degree of tension before the brass kicks in.
Speaking of which, the brass offers a new focus. Before, the OM5e could be ever so slightly strident at high volumes, the brass barking slightly which didn’t do a lot for listening fatigue. The 2M Red cut that notion out right away, giving the brass a new, slightly darker presentation that added new detail.
So, a good start and, obviously, tremendous value for money. All of that for just £89?
Next up was the 2M Blue. The cartridge remained, therefore, and I reached for the 2M Blue stylus.
Once the new stylus was in place, this sonic change was interesting for a different way. The new stylus improved the sound, yes, but it also changed the sound structure. That is, the midrange now had a very smooth presentation which added a measure of elegance to the overall presentation. Giving the orchestral backing an ease and flow while the lead vocal had a slightly more romantic aspect.
Another noticeable aspect of the sound was the rise in volume. I had to lower the gain of my preamp by two notches to achieve the same volume. The 2M Blue took me closer to the action which made the sound slightly more intimate but also highlighted detail across the wide soundstage. Hence, saxophones had a sexy slurpy swing, bass had more character and the secondary percussion enjoyed enhanced precision and dropped any sense of sonic flab. So, for example, a castanet strike was now crisper.
On that same theme, another enhancement was the tonal accuracy. There was a new realism is how the instruments were presented to the ear. Drums, for the price, sounded authentic without having to be forced, the brass section had a new flow while saxophones displayed a reedy quality but in a natural, unforced manner.
CONCLUSION
I would gauge the change of cartridge, to the 2M Red and then the stylus, to the 2M Blue, as a complete success. Why? Because, with each successive upgrade, the turntable completely changed its sonic personality. Of course, such sound quality improvements are a real testament to the Essential II itself and its inherent potential. This means that, if you retain the ‘II’ and never change the default cartridge then you really are never hearing the ‘II’ in full flight and you are, in many respects never experiencing it at its very best. Further, you could also argue that you are wasting money by never pushing the II to its limits. The OM5e is a nice budget cartridge model but it actually restrains the turntable, in ultimate terms, and never lets it really fly. With the cartridge upgrades listed above, I really felt, at each step, that I was listening to a completely different and much improved turntable. Such were the sonic differences and improvements.
Next time, when you’ve had enough of the sound quality that your hi-fi is producing and you feel the need to improve matters, consider a cartridge or stylus upgrade firstly. Especially if you are limited in budget terms. You will be surprised at how much extra juice your current turntable can give you. And, even better of course, when you finally upgrade your turntable, you can take your improved cartridge with you and hit the ground running on your new deck. So your upgraded cartridge will provide even more value for money as the years roll on.
To learn more, click www.henleydesigns.co.uk
ORTOFON ANSWERS YOUR CARTRIDGE QUESTIONS
What is the lifespan of a cartridge and its stylus and which bits age quickest?
As a pick-up cartridge is a micro-mechanical device and, like all mechanical devices, they like to be used (properly). That makes it hard to say how long a cartridge will last. Their lifespan is affected most either by misuse or no use but a well set-up cartridge should provide at least 1000 hours of happy listening. After that, it all depends on the unique set-up. The part that tends to age quickest in normal use is the rubber suspension but again this part is capable of lasting a long time in a properly set-up system.
How do you slow down the ageing of both cartridge and stylus: that is, how do you best care for both?
There are two sides to cartridge care: system maintenance and cleaning.
Regular turntable set-up checks are vital, to ensure you are always running at the correct downforce and that your VTA, azimuth and anti-skate are set appropriately. If any one of these settings is out, it will affect both the sound performance and the lifespan of the cartridge. The most common setting to shift slightly over time is the cartridge downforce, so it’s important to check this. In terms of cleaning, we only recommend the use of a carbon fibre brush with your cartridge – wiping down the underside of the cantilever, toward the stylus tip, before every record is played. Cleaning solvents are not recommended, as they can cause damage to the stylus mounting cement and if any fluid gets inside the body it can cause damage to the internal workings.
The final thing to note is that you must also maintain good care of your records. Dirty records will cause damage to your cartridge.
Why does one cartridge sound better than another? What elements of the design result in improved sonics and why?
Sound quality comes from a few key factors:
- Stylus profile. This dictates how much of the record wall can be read, and therefore how much information is taken from the record. Spherical is the most basic profile we offer, while the Ortofon Replicant 100 is our most sophisticated. A stylus is also affected by whether it is ‘tipped’ or ‘nude’. A tipped stylus is mounted onto a shank, which is then mounted onto the cantilever. A nude stylus involves a whole stylus diamond being directly mounted onto the cantilever. The former adds mass, which can affect tracking ability, while the latter is the superior, preferred method.
- Cantilever. A light, rigid cantilever is able to navigate the record walls without adding any unwanted resonance to the signal generation.
- Suspension. The suspension needs to let the stylus track where it needs to go, while still maintaining a consistent contact with the cartridge’s internal generator system.
- Magnets and coils. This is where the electromagnetic induction takes place. Tightly-wound high-purity coils and strong magnets will be able to generate the cleanest signal.
Why is moving coil deemed better and moving magnet?
To create a moving coil cartridge involves more advanced manufacturing processes. Fundamentally, the way the signal is generated – by a coil moving between magnets, rather than a magnet moving between coils – allows for the electrical signal to be more consistent and responsive. This results in a fuller, more dynamic sound performance. Because of the greater ability of moving coil designs and the greater time required to make them, manufacturers then tend to also reserve the more premium components they have for moving coil products.
How do you install a cartridge? What are the common mistakes that some users make when installing a cartridge?
The most common mistake is to simply plug a cartridge in and screw it into the tonearm/headshell. In order to read a record groove as accurately as possible, the cartridge needs to be accurately aligned to the record groove, with no other forces exerted on it except the vertical downward force applied by the cartridge. To properly align a cartridge you will need a two-point cartridge alignment protractor – which are widely available across the internet. To set the VTA and azimuth (the two other most important settings), consult your turntable manual.
Are there are tweaks that you can make to improve the sound when fitting a cartridge? That is, even though you’ve installed one correctly, is there any advice on little enhancements for the ‘tweaker’ out there?
We only ever recommend following the manufacturer’s instructions. We believe it’s the system (i.e. the phono stage set-up, or the type of speakers/amplification you use) that should help you achieve the sound you want. However, there are lots of people out there who try different things with their set-up, and as with all hi-fi it is down to preference if you want to try and play.
Does it matter what arm you install a cartridge into? Is there a synchronicity between some arm and cartridge types? and voce-versa? Maybe this cartridge chassis works really well with this arm materiel, etc?
There is definitely a synchronicity. As the sound you want to achieve is entirely personal, the best thing to do is audition the arm and cartridge together to see how the combination works for you. The one technical factor to be aware of when auditioning more esoteric products is resonant frequency. This tends to be a very rare issue where the joint arm/cartridge mass is either very high or very low. When you have a problem with resonant frequency, the sound quality can be greatly affected – and all you typically need to do is consider a higher or lower compliance cartridge, depending on what the effective mass of your arm/cartridge is.
Does it matter what type of screw you use to attach the cartridge to the arm in terms of what the screw is made from and the length of the screw? Should you use a washer or not in sonic terms?
Ortofon provide precision-machined bolts with all their cartridges and we always recommend you use these. Ideally you want the cartridge directly-coupled to the tonearm, so washers should be avoided where possible.
Hi Paul,
I bought a Rega Queen special edition turntable on June, with the objective of getting into this world. I plan to gradually make several upgrades in all the system and a cartridge is one of the first in the list.
In this regard, I have been hearing very good reviews of a Shure cartridge, model M97xE and I would like to hear your thoughts before buying any piece. What do you think about the Shure cartridge, is it good value or one of the cartridge in your article is a better option?
Also, I like the price of the Shure cartridge, which I think is very similar to the Ortofon Red price. However, I would be willing to spend some more money if I get a much better result. Do you think I can find better options at this price point?
Many thanks in advance. Your posts are really very informing.
Andrés
Ah, yes, the Rega Queen turntable. That’s an interesting design. Are you aware of it’s unique points? Check out my interview with Rega on the deck here: https://theaudiophileman.com/queen-studio-collection-pt-2-engineers/ (scroll to the bottom) along with information on the vinyl discography box set from Queen (this is Part 2 but a link to Part 1 is in the intro paragraph). The Shure is an excellent cartridge (as is the Ortofon), but I wonder if the Goldring E3 has surpassed that now even at a similar price. See what you think via the review link here: https://theaudiophileman.com/goldring-e3/
Hi,
I currently have a Pro Ject Essential II with the standard Ortofon OM 5E, that I want to upgrade to the 2M Red. I have a question though- what is the anti-skate setting and do I need a heavier weight?
Hi Bud – good choice on the cart. The anti-skate will be the same as the tracking force. The ideal figure will be 1.8g and the arm will be able to handle that with no problems.
Hi Paul
I have recently rediscovered vinyl & think it is about time I replaced the Nagaoka MP100 cartridge bought 30 year’s ago with a month’s student grant money on my Garrard DDQ 650 turntable.
Am looking to spend < £300 & would be grateful for any suggestions
Hi Jez – I think this was one of the company’s final designs before it bit the dust. A decent deck but the motor could be better, shall we say. Which is a gentle way for me to advise you not to upgrade the cart but to, in fact, upgrade the turntable. Basically, I wouldn’t go any further than the MP100 with this deck. I would look at a Rega Planar 1 for ¬£248, instead (or, even better save ¬£375 and get a Planar 2). Later, you can upgrade its cart for even better performance. In fact, your MP100 would do quite well in it.
Hi Paul, Sorry for the delayed response.
Thanks for the advice, am struggling to reconcile discarding an 18th birthday present for a newer model, emotional attachment.
If however I was going to go the whole hog & replace turntable & cartridge what would be the best combination for a sensible (<£750) amount of money, have a Cambridge Audio amp & pre-amp with freestanding Monitor Audio Bronze BX5 speakers.
Cheers Jez
Am currently buying new recordings & vinyl versions of downloaded music (electronic/dance in the main).
Hi Jez – I would get a Gett! 🙂 I’ve review it here – https://theaudiophileman.com/gett/
Hi Paul, Thanks for the input of 3 years ago, unfortunately my plans changed & due to downsizing now have a different quandary.
Current situation is music room is set up in converted loft, around 12′ x 14′ with a pitched roof.
The BX5s can’t sit against the wall as the drop below the roof pitch is shorter than the height of the speaker so I’m looking at potentially replacing the whole lot with a bluetooth turntable & bluetooth shelf speakers so that I can stream from the computer as well as vinyl.
I see the constraints as acoustic rather than budgetary & I see no point in paying a “fortune” for a marginal improvement in sound quality given the less than perfect room dynamics.
I’ve compared the Cambridge Alva with the Project E & the Elipson Omega 100 & am wondering whether the additional ¬£500 or so is worth it?
Thoughts would be appreciated
Fair points, Jez in terms of the balance between practicality, sound quality and usability. First up, I can’t make an absolute judgement on the Alva because I haven’t reviewed it but colleagues tell me that its good. Not amazing, but good. If that helps at all. Bluetooth though is the leveller here and will limit any finer sonic elements. It’s great for what it is and ideal in your situation but I too wonder about spending out. The Pro-Ject T1 BT might be worth a look at around ¬£400.
I have the Essential III & I would like an upgraded headshell & tonearm, if possible. ??? Any other upgrades possible?
Hi Thomas – for a low cost budget design such as this, a tonearm upgrade – a major upgrade – is unnecessary. You’d be better spending your money on a superior turntable. Tonearm upgrades are a good thing and you should be praised for considering it, to get the most from your turntable purchase but not here. Upgrading the likes of a tonearm is best done when your turntable reaches the ¬£600-¬£700 level and up.
That said, there are other upgrades to consider that will enhance the sound quality of the III. Look out for my upcoming feature in the next day or two on this very subject! 🙂
“replacing the cartridge with an Ortofon 2M Red cartridge for ¬£89.”
“After that, I‚Äôm going to replace the 2M Red stylus with a 2M Blue stylus (¬£130). This is a nice little upgrade path offered by Ortofon which means that you don‚Äôt have to buy the next cartridge model up the ladder (the 2M Blue) off the shelf for a whopping ¬£175.”
Why would you buy an Ortofon 2M Red and then upgrade the stylus to a 2M Blue? In total, the Red cartridge and the Blue stylus will come to ¬£219. It would be much cheaper just to buy the Blue for “a whopping ¬£175.”
Hi VinylMan- Well, you might buy the Ortofon Red with the turntable or that, in itself, might be an upgrade. You might not have the money to buy the Blue there and then. Not everyone has that sort of cash. Then time may go by…and then go by a bit further…and then you might wish to upgrade to a Blue when funds allow.
An even cheaper route would have been to replace the OM 5se with the OM10, then OM20 stylus, retaining the original cartridge.
There are many threads across the internet, but basically the 2M series is just the OM series in new….bulkier….clothes.
OM10=2M Red
OM20=2M Blue
OM30=2M Bronze etc….
Thanks for your thoughts, Graham. Allow me to make an additional point that the ‘clothes’ you mentioned also play a full part in the sound quality of any cartridge. Which is why some carts go naked! 🙂 (i.e. many van den Hul models)
Hi Paul,
Have you had much experience with the Primary E and upgrade options? Thinking of replacing the standard cart with a 2M Red but wishing to see if anyone has done this before. Thanks for your time and super clear reviews.
adam
This is a good question because the E is a sub-budget design (under £200) so you have to ask, is it worth attaching a £100 cartridge to this thing?: https://www.henleyaudio.co.uk/products/2M-Red?CategoryIds=9
I would say yes, go for it and couple it with a budget phono amplifier – an external model that is – as a further upgrade. What amp and speakers are you using Adam?
Further upgrades? Add a cork mat (Pro-Ject Cork-IT) or, even better, a cork/rubber combo mat.
Hi Paul,
Thanks for your article. Even I have a Primary E (purchased very recently) but the OM5e isn’t really cutting it for me and want to upgrade the cart. (Honestly, I wish had done more research on this model before taking the plunge!) Hence, I’m not looking at high-end carts now, but the new Goldring E-series has caught my eye (& ear). So thinking of fixing an E1 maybe.. What are your thoughts/advice on this? Do you think this is something I could carry out successfully?
Thanks for your question, Shem. The E1 is an excellent cart and a great design but, for the ‘E’, I’d go for this Audio-Technica: https://eu.audio-technica.com/AT-VM95E?search=at95 which arrives with an elliptical stylus tip. The latter will extract more detail from the grooves.
Have a question if I may ask. I have an older Ortofon cartridge an LM-10 mounted on a JVC QL-Y55F turntable (straight arm), just noticed the wiring diagram for the ortofon cartridge and the diagram in the manual for the JVC is different. I have the cartridge wired to how Ortofon shows it and it sounds fine, balance is correct left to right. The way it is wired looking at the pins on the back of the cartridge is upper left – White, lower left – Red, upper right – Green, Lower right – Blue.
Per the JVC manual it shows Upper left – White, lower left – Blue, upper right – Red, lower right – Green.
Should I leave it the way it is or match the wiring to the way it shows in the JVC manual?
Thanks
Hi Tony – my gut reaction would be to follow Ortofon’s advice. That JVC manual, does that refer to a JVC cartridge that was original supplied with the turntable perhaps?
Thanks, I know the JVC turntable came with a JVC MC cartridge the MC200E (outside the US, where this was purchased), I have not found the wiring diagram for the JVC cartridge other than what shows in the owners manual yet. I’ll leave it the way it is as it does sound ok.