The Article
Goldring E3 Cartridge: toting a super-elliptical stylus
30th July 2017
Goldring has been in business since 1906, so it’s about time Paul Rigby reviewed one of its products then, eh? It has waited long enough! In this review, he tackles the new E3 cartridge
The company recently announced the launch of its E series of cartridges. All relatively low cost and all of interest to either budget users or those looking to upgrade their introductory cartridge with something rather more interesting.
The three units in the E series are based upon Magnetic Duplex Technology (you can add a ™ in there, if you wish). The idea behind the technology is to improve stereo rendition. Both the E1 and E2 models include spherical styli with a choice of cantilevers. The E3 model, which I look at here, has an aluminium cantilever – the same unit used on the E1 and E2 – but adds a “superior bonded”, super-elliptical stylus measuring 0.3 x 0.7mil. This is what attracted me to the E3, I was looking for a blend of value and high frequency groove detail retrieval as well as sibilance reduction. Especially as a basic elliptical stylus measure around 0.4 x 0.7mil. Compare those measurements too with the E1 and E2’s spherical tip at 0.6mil.
According to Goldring, “The E Series cartridges use a specially designed adjustment screw to locate the cantilever, rather than the standard xed pin, allowing micro-adjustments during production. This pre-set azimuth means crosstalk is already optimised and the cartridge can be safely installed in a typical turntable with no correction required.”
During the record mastering process the cutting lathe records stereo information as a ‘V’ shaped groove which has perpendicular side walls angled at 45°, “Conventional moving magnet cartridges,” added the company, “use a single large magnet that interacts with two vertically mounted coils to produce a stereo signal from the groove. This can introduce crosstalk and so only offers a modest amount of stereo separation.”
This is why the Goldring E Series cartridges feature a dual magnet arrangement, “Magnetic Duplex Technology uses two low mass magnets which interact only with their partnering pickup coil, angled at 45° to match the cutting head arrangement. This enables the cartridges to more accurately trace the record groove because they precisely emulate the geometry of the cutting head, making for better stereo separation and a more accurate, involving and musical soundstage.”
I was happy to see that the Goldring chassis features threaded screw holes inside the chassis itself. This is a £100 moving magnet cartridge and thus will feature in the hands of beginners or cautious vinyl users possibly unfamiliar with regular cartridge fittings. The last thing you want to do to a nervous hi-fi installer is tell them to juggle tiny screws that dangle outside of a chassis, adopting odd and scary angles depending on how you hold them, with tiny nuts that threaten to ping off into a dimension occupied solely by cartridge nuts, pens and odd socks and then try to tighten the entire thing with a tiny screwdriver while, at the same time, avoiding the cantilever! It’s bad enough asking an experienced hi-fi journalist to do such a thing, never mind an uneasy music fan. Goldring have got this part of the design right.
Fitting the Goldring to my tonearm (with 2g of downforce) was intriguing mainly because, once in there, it looks absolutely enormous! It reminded me of some of the cartridges used on hi-fi in the 60s or even the 50s. The Goldring chassis is obviously a nostalgic reflection on times when men were men and cartridges were the size of an articulated lorry. Yet, the very largeness of the thing also helped in terms of installation. It imbued more confidence during handling.
SOUND QUALITY
I began by playing the original pressing of Nancy Sinatra’s LP Country, My Way, produced by Lee Hazelwood and the track, It’s Such a Pretty World Today, a wholly romantic, even twee song.
The initial impression was an over-whelming sense of focus from the Goldring. This track had Sinatra’s voiced pushed down a classic echo chamber and so, even the slightest midrange smearing combined with excessive noise will puff out the voice in a cloud of nasty distortive attack. The Goldring took immediate control of any potentially wayward frequencies and reigned in the Sinatra voice to give her delivery a rather playful and wistful quality. The echo chamber obviously still remained as an effect but Sinatra’s voice presented welcome femininity instead of Goldzilla in a skirt.
This focus also leant itself to aiding the backing singers. Their harmonies tended to rise in the higher registers which only added to the smeared mids. The new level of precision, though, added welcome harmonic textures that gave the vocals a layered richness.
Another element that could have suffered from the loose upper mids was the notable twangy slide guitar. The Goldring provided a sense impressive detail from this instrument. Speaking of which, the Goldring’s lower noise performance meant that the piano popped out of the mix, giving a tonally realistic performance. The piano, on this track is an adjunct to the main song but its an important one that gives breadth to the soundstage.
Percussion and bass also now had a greater sense of recognition because the lack of bass bloom drew them both from a blacker background. Hence, the new level of clarity enabled the ear to pick up a new sense of impact and strength from this area.
Another notable aspect of the soundstage were the acoustic guitars, the attacking strumming on the right channel and the subtle strumming on the left. Both offered tremendous midrange insight and musicality that added a sense of speed to the performance.
I then turned to the post punk vibes from Die Werkpiloten via Germany’s Vinyl on Demand label from 2012.
This is a drum-heavy LP, fast paced percussion and high energy to boot and I was impressed by the organic nature of the drums. The Goldring gave the music impact and power and a real sense of pace but kept in touched with the humaneseque nature of the drums, rounding their edges just enough to prevent and sense of the clinical.
The low noise approach to the Goldring also enhanced the instrumental separation along the soundstage, giving each instrument a sense of space to perform at its best. The soundstage never felt crowded or stilted and the lead vocal thus provided an emotional yet flowing performance.
CONCLUSION
Sensibly designed for use by beginners or vinyl fans with minimal hardware experience, the considered design of the E3 provides a sense of clarity and midrange purity with a bass that delights in terms of information and character. In terms of the inherent sound quality from this cartridge, the E3 provides exceptional value for money. In fact, it is one of the best budget cartridges, at this price point, currently for sale on the market.
GOLDRING E3 CARTRIDGE
Price: £100
Web: www.goldring.co.uk
TO BUY CLICK BELOW:
USA – https://amzn.to/2TPSslC
EUROPE – https://amzn.to/2GkAYuE
GOOD: focus, precision, clarity, midrange control, bass impact, design, price
BAD: none
RATING: 9
REFERENCE
Rega RP3 turntable
Ortofon 2M Red
Trichord Dino phono amplifier
Rega Brio-R amplifier
Spendor S3/5R2 speakers
Tellurium Q cables
Harmonic Resolution Systems Noise Reduction Components
All vinyl was cleaned using Audio Desk’s Ultrasonic Pro Vinyl Cleaner
Hello Paul, and thanks for the review and all the info. Great job.
I have the Onkyo CP1050 turntable with the Goldring E3 and the sound is really amazing, i’m discovering new details on my old vinyls. I’m using a Yamaha AS-1100 amp with Monitor Audio Silver2 loudspeakers.
I’m just curious about the next step on sound quality, which cartridge-stylus? Have i reached top sound quality with this turntable? What do you think?
Thanks in advance
Thanks for your kind words Tomas and yes, you’re right, the next stage is a turntable upgrade I reckon. Save your cash for something up around ¬£700-¬£1,000. When you get there, let me know and we’ll chat.
Thanks for your reply, Paul.
I bought the Onkyo turntable 2 months ago, and i’d like to extract all of its juice for some years, I’m really happy with it, i think it is a great product for the price.
So i was thinking of giving a try to one of these stylus when the E3 get worn out:
– Ortofon 2M Bronze or Goldring G-1042 as MM.
– Audio-Technica ATF7 or Denon DL-103R as MC.
So do you think any of this options isn’t worth a try? Is my best option keep replacing the E3 with the same?
Thanks again.
Ahhh, well, that’s different then 🙂 I would go for the 1042 and stop there. I’d save your MC upgrade for a better deck. Saying that, the 1042 is a top quality MM cart and fights its corner well against low priced MC carts.
Make sure you have an external phono amp.
Look at where you’ve sited the deck. Make sure it’s on quality shelving.
Upgrade the cables, QED provide good value – the best you can afford.
Detach and remove the lid during play (removes lid vibrations) and then freely place it on the plinth to keep the dust out when not in play.
Consider a stabiliser (removes bearing noise) to fit over the spindle. HRS is excellent but not cheap. There’s a few more on my site in the accessories section.
Upgrade the headshell (do this before you buy the Goldring – Timestep offer a classy option, enhances rigidity): https://theaudiophileman.com/t-01hs-ebony-headshell-timestep-review/
Add isolation feet under the plinth. Again, removes veiling noise.
You can do all of this over time, when funds allow but that should keep you occupied for a year or two 🙂
I’m off on my holidays for a week now. If you ask further questions, I’m afraid they won’t be answered for a week or more. Good luck with the upgrades!
Many many thanks, no more questions, i’ll follow your advices, they sound as excellent choice.
Thanks again and enjoy holidays!!!
I have a Vintage Pioneer PL-600 in excellent knick and would like to know if you would recommend the E3 for it.
Regards Mark
Hi Mark
Is this the earlier direct drive model or the later belt drive model?
Hi, Paul. Thanks for your excellent review of E3 and just in time when I am thinking to upgrade my old AT311EP MM stylus. I am from India and using very old Indian turntable (30 years old). The turntable is still in very good condition and enjoying vinyl sound from it. Only down side of this table is that it has no height adjustment provision and tall cart may pose problem due to rear of the tall cart may hit record while playing. My present AT311EP cart has only 1mm gap from record surface to rear of the cart. I am using recommended VTF of 1.25gm. As the E3 is tall cart and its height is 18mm to the stylus tip I am little bit worry of upgrading to excellent E3 cart. Currently I am not in the mood of upgrading my turntable. Kindly advice.Thanks.
Thanks for the query Amal – I find it odd that most cartridge manufacturers don’t readily supply dimensions to their carts, very odd. Hence, because I don’t have a AT311EP to hand, I cannot measure it for you. Looking at it, though, I would say that the E3 is larger. How it would sit on your turntable is, I’m afraid, a bit of a mystery. You may be ok but you’d have to borrow a sample to find out. If you are at all nervous about it, though, then you might want to look at an Ortofon 2M Blue or AT VM520EB.
Thanks Paul for your quick reply. My cart AT 311EP measurs 20 mm from top of headshell (headshell 1.5mm thk) to stylus tip. Regarding 2M blue, all 2M series carts have same vertical dims i. e 18mm from top of headshell to stylus tip. Don’t know about other you mentioned. Disappointed for E3. Anyway thanks for suggestion. Amal
Of course! I should have asked you to measure it for me. Forgive my dozy reply. Well, you’re in luck because the E3 measures 18mm to the stylus tip. So you should be fine! (Or 19.5mm inc headshell).
Thanks again for quick reply. Glad to know that I can still use E3. However my advice from you, how the Goldring Elektra cart! It has great reputation among budget audiophiles. Thanks. Amal
I would prefer the E3.
Hi Paul,
I’ve been a hi-fi ‘nut’ for over 56 years; thanks for your accurate review of the E3 – I can report your conclusions concur with mine. I installed my E3 tracking at 2g on a much modified Rega P1 (2016) including a replacement Rega RB202 tonearm and a 3mm cork mat. I can confirm that no spacers were required to result in a completely level tonearm. I currently use a Denon AVR-X6200’s built-in phono stage into Q Acoustic 3020s via QED silver cabling, and the result is exquisite. Thank you for your continued and valuable contributions to hi-fi journalism.
Goldring E3 Cartridge.
Hi Paul,
Thanks for an informative and excellent review. I am seriously thinking of investing in the Goldring after watching the latest HiVinyl review on Youtube (Grado Presstige Black 2 vs Goldring E3). I love the Grado sound and have Gold Prestige 1. I would have thought the Grado would have a deeper, cleaner, more extended / controlled bass, but it seems the Goldring was the champ. Also, it seems there maybe a ‘quality control’ issue with the Grado’s with either skewed cantilevers or one channel completely dead. What’s your opinion on the Grado Black / Green vs Goldring E3? I love a rich, warm sound with an expressive midrange, smooth detailed extended treble, and strong deep articulate bass.
Regards,
Fraser Campbell.
I wish I could provide comprehensive information on this one and apologise that I cannot. I have yet to do a thorough review of the Grados (they obviously need to be on my review list). I’ve heard them and they sound nice but I haven’t done a proper test. I do know that the E3 is excellent but I am personally not sure how it measures against the Grados. Again, my apologies.
Hi Paul,
Many thanks for your response. I look forward to your reviews of the Grado cartridges.
Regards
Fraser Campbell
Hi again Paul,
Is there any chance of pairing your E3 with a Tisbury Audio Domino Phono Pre-amp for a combined review? From all accounts they should be a synergistic match made in heaven…
Hi John – Indeed. I thought a review sample was on the way but everything went a bit quiet and I know not why. Thanks for the nudge.
…another item I meant to suggest for appraisal was LP Gear’s Carbon replacement stylus CFN3600LE for the ubiquitous Rega Carbon – the carbon cantilever, fitted with a fine-line elliptical stylus in lieu of the conical, transforms this cart into something really special! Assuming you have access to a Carbon body, I can let you borrow a new one I was saving – as long as you promise to return it post review of course…
Thanks John – the loan shouldn’t be necessary though. Many thanks for the offer, though 🙂
Hi once more Paul,
Carrying on from our Sept. 2018 chat, after a while upon a foolish impulse I sold my E3 to fund a G1042 – and eventually wished I hadn’t. I am currently in the process of purchasing another E3, and wonder if you can remember from your original review which alignment details including nulls you used to achieve the sound you so eloquently describe… copying being the sincerest form of flattery…
Hi John – I *think* I was checking out a paper-based gauge from Polaris at the time. So may have used that. A quick Google should locate it.
Thanks Paul, I’m unfamiliar with Polaris, but will Google as suggested.
Hi Paul.
Belated reply/update herewith; Polaris traced and resultant sound found wanting. Following several months trying nearly every protractor in the known hifi world I have eventually discovered my ideal – and I so wish I had discovered it prior to selling on my G1042…
My current table is a modified P3 using an aluminium sub-platter, upgraded belt, P6 counterweight, and replacement acrylic table, using a Rega NEO MK3 PSU. A P6 in all but table base material.
I modified a Vinyl Engine downloadable standard Rega single point 58.6mm arc protractor, reducing the arc to 58mm dead. The result was all four of my carts (and my ears) have benefitted from the very best reproduction I have ever achieved in 60 years continuous hifi tinkering, and when you get time I urge you to consider trying this alignment for yourself for a couple of hours – you’ll never really know if you’re getting the very best out of your test equipment unless you do…
Keep up the good work Paul.
Thanks John – I’ll certainly check it out.
Hello Paul,
I have the chance to buy an Áudio Técnica VM530EN for 100€.What you think?Or should I spend 120€ instead and buy the Goldring e3?What is my best choice?
At that price – go for the 530.